Saturday, January 31, 2009

Qualifications For Mac Makeup

Wood fiber insulation

wood fiber insulation are mainly from local wood residue and thinning as well as from waste produced during the wood processing industry produced.

in the production of insulating material, the wood under pressure and heat disintegrated and then pressed into sheets. Noteworthy is that take the material contained in the main function of a binder resin, there are no extra materials are used. ensure

qualify for protection from the weather, the wood fiber insulation boards are equipped with a layer of bitumen, which, however, in case of fire, a possible source of exposure can represent.

wood fiber insulation are available to bond with water glass, this glass of water while delivering the wood and fire protection. Water glass contains no harmful substances, such sheets can be easily treated to be recycled. They are mildew and compostable.

extends the use of wood fiber insulation to insulation boards in the development of sound insulation panels to the floor area. Because of their structural and physical properties of wood fiber insulations are ideally suited for permeable construction methods.


Building physical and economic data

density 400 kg / m³
Baustoffklasse B 1
thermal conductivity l R 0.09 W / (mK)
water vapor diffusion resistance factor m 2 - 5
material price for 10 cm about 50, - DM / m²
material price to achieve a k-value of 0.4 W / (m² K) about 110, - DM / m²

applications

outer wall thermal insulation constructions
roof under rafter - Insulation
massive ceiling -
perimeter insulation -
wall / ceiling with lightweight construction planking of lightweight walls


following pollutants may be present: terpenes

source: enius.de


Women And Men Wrestling

Baumwolldämstoffe

The raw material for cotton insulation are cotton fibers, the improvement of performance in case of fire (class B2 and B1 to DIN 4102) and for resistance be treated against mildew and pest infestation with borate compounds. Cotton insulation materials have good heat and sound insulation properties, they are rot-proof and can even be composted as a function of the boron compounds used.

Commercial insulating mats, in addition to sound-deaden and also bulk and so-called Dämmzöpfe available, which are all distinguished by easy processing properties. Cotton can be used in wood frame exterior walls as insulation between the rafters, bearing insulation on the suspended ceiling systems, insulation of lightweight partition walls, sound insulation, cavity insulation of partition ceilings, floor-interior-side external wall cladding and wall insulation.

The physical properties of cotton fibers, such as moisture management, and diffusion capabilities, the indoor environment is positively influenced.

are as raw, untreated chemical and pesticide residues examined cotton fibers used are cotton fiber insulation classified as biologically and ecologically advisable.

Building physical and economic data

density 20-60 kg / m 3
Baustoffklasse B 1 or B 2
thermal conductivity l R 0.04 W / (mK)
water vapor diffusion resistance factor m 1-2
material price for 10 cm about 30, - DM / m²
material price to achieve a k value of 0.4 W / (m² K) about 30, - DM / m²

applications

outer wall infill of timber stands
roof insulation between rafters
solid ceiling -
perimeter insulation -
wall / ceiling with lightweight construction infill of uprights and beams

source: enius.de

How To Make Ice Skate Invitation

sound - basic information

The term "insulation" in principle to distinguish between sound insulation sound insulation.
The airborne noise, for example the noise from the apartment next door, for example, voices and music. In many cases, the sound made by sound-reflecting obstacles, just through a wall or panel, or even a curtain. Especially for the separation of housing and outer walls but may require special measures. Concrete walls generally produce a good, adequate sound insulation. Wall panels in contrast, must be a multi-layer structure or a suitable intermediate layers (eg pulp) made sound-absorbing. For exterior walls, various interruptions of the wall structure, such as roller shutters, window, radiator niches degrade the sound insulation of the wall. This must sound here byways can only be avoided by well-executed designs. In

sound insulation to reduce the transmission of impact sound is understood, for example, when walking on a ceiling or the chair back is generated - the rumble is always lying about the apartment. The impact sound insulation is achieved by the blanket and a elastically resilient intermediate layer under the Gehbelag. This is often extruded polystyrene rigid foams are used.
The sound insulation in private housing is free. For multi-party buildings the sound insulation according to DIN 4109 geregelt.quelle: enius.de

Saturday, January 17, 2009

Infiniti G37 Vs. Bmw 325xi

roof slab of aluminum

aluminum

Kalzip standing seam and profiled dress sheets are available as standard in a stucco embossed finish that is achieved by processing the natural Mühlendematerial by embossing rollers. This provides a surface that scatters the light reflectance and glare reduction.

Because aluminum is durable and durable, it provides excellent service as a roofing material or clothing without the need for any protective covering.

after prolonged exposure to the elements, reflecting the dull Surface of the template in a high degree of aluminum down to a constant patina execution and changes in appearance are constant along any lift.

The weathering effect is (above) illustrates the City of Manchester Stadium, England very well. Within just 12 months of the original roof had dampened down. Once the new North Stand was appropriate, he also began to lose much of its high reflectivity and toned down to the original material Kalzip together.
source: archiexpo.de

Free Clips Of Brent Corrigan

acoustic panel - Acoustic roofing panel

acoustic

There are many occasions where a Kalzip requires roof system, increased acoustic be. Some buildings, due to their position (eg close to an airport or a busy city center) to prevent excessive external noise, while others require for internal use or process (eg concert hall, engine test facility, etc.) that the internal noise is included. A contributing factor is mainly to reduce the ability of a roof system, the effect of the scattered sound, the total mass of the system. Other factors include isolation and localization.

Kalzip systems able to accommodate a variety of acoustic performance requirements by incorporating other layers such as high-density insulation, acoustic boards and flexible membranes to provide increased noise reduction performance available and will be amended by the perforation of the film to provide improved performance of sound absorption.

Kalzip acoustic board is a high density cement particle board that can easily be incorporated into a Kalzip system to increase the mass and after the noise reduction properties of the system drastically.

Kalzip acoustic membrane is a high-density rubber-Polyäthylenton Schrankeenmembrane that can be easily incorporated into the system and to increase the mass and improve the sound reduction properties afterwards. The acoustic diaphragm Kalzip is usually used in conjunction with the Kalzip acoustic board and may act as an insulator between the boards and the more acoustic performance erhöhen.quelle: archiexpo.de

Tattoos Of Stars On Stomach

semi-rigid acoustic fiberglass

isolation

Kalzip insulation products conserve energy through their use by the reduce requirement to cool to heat the building or, limiting CO2 emissions. They are also free HCFC and HFC and have a possible assessment of the global (GWP) of less than five warming

The most common insulation used is a Steppdeckeart, non-hygroscopic material that absorbs no moisture, but they just keep on the surface to take place of its fibers, thus stimulating the evaporation.

The use of a compressed insulation, completely filling the roof, which is empty of the vapor control layer, together with the breathability of the Kalzip sheet lined negates the need for a Entlüftermembranenmaterial Kalzip within the system.

Kalzips range of insulation products include glass fiber and rock quilt, flexible and high-density disk drive. At the heart of the range are Kalzip isolation plus 35 and plus 37, the mineral wool quilts are high performance, offering high-performance thermal performance.

To further complete the route, are glass and rock fiber insulant present requested a wide variety of thermal performance values together with the flexibility of use in offering the additional acoustic performance wird.quelle: archiexpo.de

Lia Sophia Prizes For Games

sound insulation classes for window insulation

In Germany, the sound insulation of windows is divided into noise control classes. The allocation of soundproofing to the rated classes sound reduction and examples of the glazing in the following table:


To calculate the required sound transmission loss of windows is also the appropriate rules to be observed. Depending on the application it comes with the same Immissionsverhältnissen significant differences. Based on a busy road through the design of the window was measured at different sets of rules (source Bavarian State Office for Environmental Protection). In the graph the required sound protection class of the window for a bedroom for different distances (different mean level) of the immission is shown from the middle of the road.

The highest noise control classes are made according to the DIN 4109 [Interior level 25 dB (A)]. According to calculations by the 24th BImSchV are the sound insulation classes sometimes lower by 2 classes, to be adopted as the internal level (upper Reference value) at 30 dB (A).

sound insulation class of windows in different regimes


source: fenster1.de

Friday, January 16, 2009

Wedding Cake Toppers With Shrek And Fiona

First, the heat pump, then insulate the savings gradually

also suffers Financing: If you decide at first for an insulation, a lower cost saving results as by installing a heat pump would be possible. This also restricts the financial means and with rising oil and gas costs are the positive effects mostly disappeared quickly. You finance a geothermal heating system, however, a KfW loan with a maturity of 20 years, so can the debt service paid from the savings. This is at a Insulation measure due to the reduced efficiency was not possible.

These considerations should not contradict the meaning of the demand reduction, but also show that the order should be chosen with care of the remedial measures to economically handeln.quelle: Stoltenberg-energie.de


Chinese Men Shaved Pubic

Rising prices for oil and gas, the cost savings of a heat insulation make fast The existing buildings

you decide for insulation instead of a heat pump, so you are also deprived of much more important than the effects of primary energy savings: cost of stability and energy independence. An insulation reduces the heat requirement, the conventional heating system persists, however. This results continue Emissions, maintenance and chimney sweeps are considered and, ultimately, rising oil and gas prices continue to go fully into account the cost of heating. If the effect of reducing demand when prices are rising already repealed the medium term, the heat pump would continue to ¾ of the heat demand by providing free geothermal energy available. It is this relationship to the stability and independence leads to heating (a 10% increase in electricity tariff charged only for ¼ the cost of heating processes, but the heating costs also rise by only 2.5%) is.

Often it is also argued that investment costs for a first right, after subsequent implementation of insulation measures, however, make large geothermal heating, such a procedure uneconomical. One example is a 200 m2 house, built in the eighties used, which would be supplied by a 15kW heat pump with borehole 225 meters. This would require about 30,000 €. If one now an insulation from unraveling and reduces energy consumption by 20%, could be enough of a heat pump with 12 kW and 180 meters of ground probes. This facility would, however, still an investment of € 27,000 required, so that ultimately € 3,000 could have been avoided. In this case you forget, however, that after the insulation, geothermal heat is more widely available and reduce electricity costs disproportionately for the heat pump to reduce demand. The pay of "excessive" heat pump system would therefore only have a disproportionate erhöhen.quelle the payback period: Stoltenberg-energie.de


Removing Stains From Stainless Steel Cutlery

niece to reduce the number of possible insulation measures often clearly a

addition to profitability also the existing buildings often limit remedial measures so that the range of technically feasible insulation options , is reduced to a manageable level. Ultimately, there are often only the filling of the voids between masonry and brick, new windows and roof insulation. This should be considered in principle that the windows remain always the coldest place in the wall, otherwise the risk damp walls. The replacement of windows as a single remediation approach is therefore to be regarded as problematic, so that a clean-up are again limited to roof and walls or carried out in combination with the renewal of the windows must.

Plant is an expensive thermal insulation, which has in economic terms, the highest payback period, it has to be physically so that no damage is caused by moisture. To ensure this later, in winter the regular airing of the daily requirement. Install a ventilation system with heat recovery is not necessary to this course. In addition to high investment costs, which should also evaluate the cost of insulation measures are added, the air humidity can decrease the interior uncomfortable, so here, for example by Wassernebler and indoor plants used again must be remedied. An individual planning assumes these effects are largely vermeidbar.quelle: Stoltenberg-energie.de



Slave Bracelets Symbolize

heat pumps are more economical than insulation measures

The decision is for a heat pump often taken as a function of the existing insulation of the house. From an economic perspective, however, heat pumps are in poorly insulated buildings the most economical. Since this course contradicts the ethos of the primary energy reduction, rehabilitation willing to face the question: First, the first insulation or a heat pump? The completion of both measures is not to finance often. Since the question of the order of energy consultants is usually answered with an unequivocal made first house insulation, shown by the following considerations to starting points, refuting the conventional wisdom and clearly illustrate why you should first install a heat pump, and then to gradually from the savings to insulate the house.

First of all, the relative savings in heating costs
a clear argument for the heat pump. This achieves savings in buildings by 50%. A
average investment for the conversion in stock usually costs € 25,000. Substituting both quantities into the relationship, then an amortization of 10 years to calculate. To repay an insulation measure is similar savings achieved, usually well above 20 Jahre.quelle: Stoltenberg-energie.de



Why Does A Toothache Hurt

basement insulation is missing almost always

modern buildings have a insulated base plate, to insulate the basement walls is planned on the outside. In contrast, old buildings remains primarily a retrofit insulation to stop the high energy losses. A basement that is heated and used in, to insulate later, but is extremely expensive. Here it is worthwhile to reconsider the use.
source: energy-saving-the-haushalt.de

Weakness In Pokemondeluge

Subsequent Insulation of basement ceilings

Above or below?

The thermal insulation of the basement ceiling is often too little attention. But even here there is a way to save energy with little financial outlay.

The simplest type of retrospective Thermal insulation of flat solid floors is sticking or plugging of insulation from the ceiling side. Faucet (for example, water, heating, electricity) require the retrofitting of insulation layers of special attention. Ceiling lights may need to re-fastened and their connections are extended. The maximum insulation thickness may be limited by eg directly beneath the basement ceiling, built-in cellar windows.

basement ceiling with odd and uneven bottom (caps or vaulted ceilings) are only using a sub-support structure or later dämmbar.
are most meaningful substructures, transverse to the support systems run, since the distances of these carriers usually over 1.00 meters. Otherwise you will need a stud again be appropriate to the distance of the used lining (plasterboard, plasterboard, etc.) is adjusted. All joints and connections of the edge support structure must be designed so that an uncontrolled flow behind the insulation material is prevented with room air.

as material for the floor structures are suitable flexible insulating best. It is also possible to install only the sub-structure with cladding and to subsequently blow the cavity with insulation.

The insulation on the floor It only makes sense if a hobby of living space and adequate room space is available. The necessary building heights be at least 6 - 10 cm. The follow-up (eg, cut doors, radiator, set it higher) and were the entrance to the apartment resulting paragraphs and thresholds to be considered.

Do you have a cold or a hot cellar?

The basement ceiling is always under construction so designed as a floor. Nowadays, most often used in new buildings a blanket of reinforced concrete. To improve the sound insulation properties are on the reinforced concrete floor impact sound insulation placed. In general, it is the relocation of a wet stroke.

ceilings contribute significantly to the reinforcement of buildings because the walls are standing in different axes positively connected to each other and brace each other. To reduce sound transmission, a possibly existing ceiling space is completely filled with mineral wool insulation.

In basement ceilings are two possible scenarios:
  • Heated basement
  • Unheated basement
If the basement is not heated, so is the basement part of the heat-transferring enveloping surface and must be insulated in accordance with the requirements be possible to keep the heat losses to the outside. The insulation can be the top side, and in addition to sound insulation or other, in the basement, attached.

is heated the basement should be taken in the usual insulation of the floor and walls.

limits must be observed

If you want to clean up an outside wall or re-build, you must observe certain values of the EnergieEinsparverodnung (EnEV) or comply. These are usually around the U-value (= heat transfer coefficient) of the relevant wall. The distinction between buildings with EnEV a normal (> 19 °) and buildings with a low internal temperature (< 19°).

  • Normal indoor temperatures require U-values between 0.45 W / (m² K) and 0.35 W / (m² K).
  • Lower internal temperatures allow U-value of 0.75 W / (m² K).
to achieve the required U-values for buildings with normal internal temperatures are in the renovation, depending on the existing wall structure and the desired insulation material, usually insulation thicknesses of 8-12 cm is required .

These heat transfer coefficients do not have to be met if:
  • Evidence for the entire building is performed.
  • The change in less than 20% of the wall surface to the same side of the building concerned.
  • The expansion is at least contiguous 30 cubic meters.


Where and how can be insulated?

pitched roofs have changed considerably in its structure in recent decades. The task of the best tile roof was to protect the building from damage by the elements. The ample sized and often unused roof space was due to the high number of joints of roofing ventilated very well, and so provides a Humidity and temperature compensation.

housing shortage and rising construction costs, however, led to increased use of housing reserve. Thus, the period for the simple roof, a high-quality component building physics with a variety needs. The high demands on the heat, noise, fire and moisture protection are met by a layer structure that uses the property for optimum performance and building materials.

The insulation technology running pitched roofs, a distinction on the location of the insulation between rafters
  • About
  • insulation between rafters
  • Under rafters
result of tightened requirements for thermal protection (through the Energy Conservation Act EnEV) are now often used combinations of intermediate and under rafter insulation. The layer in which the sub-rafter insulation is located, is often used as an installation level.

The version with the roof insulation boards (see adjacent figure) and thus allows a continuous transfer of thermal bridging of the insulation on the rafters. The rafters can be run as a visible rafters. An additional rafter insulation is also possible.

Basic requirements

EIFS in all its layered structure as a system of one manufacturer in accordance with the manufacturer's guidelines to perform. In addition, the provisions of the relevant building regulations concerning the fire performance of the materials used, particularly the insulation materials are observed. Depending on the province and building height may be permitted or demanded:
  • Flammable materials (B2)
  • combustible materials with a strip of non-flammable insulation above window and door openings
  • flame-resistant (B1)
  • non-combustible materials ( A1 or A2)
Finally, the stability the exterior insulation system must be guaranteed. Depending on the height of the building, carrying capacity of the soil and weight of the composite thermal insulation system can be allowed or demanded:
  • bonding of insulation to the substrate without mechanical fastening
  • bonding the insulation with additional doweling
  • laying the insulation in a pegged aluminum rail system
  • dowel construction approval
  • Simplified stability proof
  • stability proof
other basic material and construction

Curtain, ventilated facades (VHF) consist of the components:
  • clothing
  • ventilation
  • insulation
  • substructure
clothing
In a VHF a wide range is of possible facade cladding as a final weather protection and freedom of design of the facade are available. Depending on the design desired, a "light" cladding or a "serious" clothing will be selected. As clothing materials are commonly used:
  • aluminum composite panels
  • Fiber cement
  • fiber reinforced Harzkompositplatten
  • wood
  • wood cement
  • high-pressure laminates (HPL)
  • ceramic
  • natural stones
  • titanium zinc
  • support plate systems for plaster, ceramic and glass applications
  • brick
The VHF is not a composite system, but the components are insulation and weather protection structurally separated from one another. The intermediate ventilation space regulates the financial climate. Use or building moisture is removed by this upwards, moist exterior walls be dry in no time. The two-tier system separates the functions of the VHF weather protection and insulation .
be used mainly for VHF mineral insulating materials for thermal, acoustic and fire protection, offer themselves for any use and building height. Insulation can be placed in any required thickness.

The substructure is the static link between the supporting outer wall and the actual cladding. As materials are steel, wood or aluminum or a combination are available. The majority has prevailed aluminum. These substructures are three-dimensional adjustable and lie down without force to the building structure. Unevenness and Wandversprünge can ausgleichen.quelle easy gieselmann.info


Does Matcha Have Side Effects

Subsequent thermal insulation of buildings

Adequate insulation of external walls and roof of a building is guaranteed for newer buildings already by appropriate government regulations, was often neglected in older buildings. Therefore, there are many older homes for energy efficiency in this regard, a very large potential to improve the energy efficiency significantly by subsequent actions performed to Wärmedammung the external walls and roof are. Who are the owners an older house decides to invest money in the subsequent thermal insulation of the house can, to a considerable cost savings from a mar. the heating of the house and go to the other in the house, due to selling by increasing energy efficiency, just in case certainly can be better or rent.

measures for additional insulation of houses are for example:

a) For the insulation of exterior walls

There are several ways to insulate exterior walls later that depend on the particular nature of the exterior walls. Thus, for the case of two-layered external walls, So the exterior walls of two layers separated by air walls are, simply inject insulating material from outside into the air layer. Another possibility for the subsequent insulation of exterior walls, as it is with monocoque exterior masonry in general, dress up the exterior walls with insulation panels that are covered only by a thin layer of plaster.

b) The insulation of the roof A roof is insulated

usually by insulation products are introduced, such as glass wool between the rafters. The cost for subsequent thermal insulation of the roof depends on whether the attic is already expanded or not. If you just from the inside gets to the rafters the work must be done without much effort, since the insulation can easily fit inside. You should not approach more from the inside to the rafters, the roof from the outside, are insulated from the decline of the roof tiles. These works are of course more complex.

Whether you want to insulate the roof of a house or the outside walls later, you should be pre-qualified advice and carry out the work, if possible, by a construction company. Although the costs of such measures are not exactly small, worthwhile However, with such long-term security. Thus, the subsequent insulation of exterior walls does already for a house of average size, often a heating cost savings of more than 500 € per year and the subsequent insulation of the roof after all, usually more than 250 € per Jahr.quelle: energy-saving tipps.com


Zeb Atlas & Mark Dalton

What can be insulated later? Why

masonry
The insulation measure is feasible in the short term and usually without scaffolding and construction site equipment. Consuming and expensive preliminary work on the buildings are not necessary. Either or mold-injection holes in the Cross joints of the walls or drilled stones taken from the walls. This can also be difficult to reach areas of the cavity layer and filled evenly. After Dämmvorgang the holes grouted or easily removed stones will be reinstated.



roof and ceiling
During the subsequent one ceiling insulation boards are 2-3 down from the attic removed from the Fußbodendielung. Then, the insulating material is introduced into the compartments. After Dämmvorgang If the removed planks reinstated



ventilation and pipe shafts
existing supply wells may later be filled with granular Rockwool. The non-combustible stone wool with a melting point> 1000 ° C according to DIN 4102 can prevent the fire spreading to other floors in the utility shaft.



vaulted ceilings and domes
The problems of classical insulation with sheets or webs include vaulted ceilings in churches, halls and curved ceilings of older buildings. For these sectors in the German Rockwool Sprühklebetechnik for the blow-in insulation system has developed. With this technique, the insulation even in designs with a slope werden.quelle applied slip-up to 80%, evenly and seamlessly: trotherm.de


Mermaid Doll With Baby And Pet 1970

subsequent insulation?

advantages of the subsequent insulation
In times of rising energy prices, a high consumption of energy more and more to the cost factor. Saving energy means saving money!

The advantages of the subsequent insulation should here the example of a subsequent layer of insulation of the hollow masonry are presented.

The injected into the existing air layer insulation, the heat flow through the building envelope will significantly change. The surface temperature of the inner walls is increased. The inner walls, beams " thus less cold from. The result is a significantly lower consumption of heating energy and a more comfortable living environment.
In the adjacent diagram of the temperature profile without / with insulation in a typical exterior wall of a house represented the 60s / 70s.

The average payback time of a subsequent core insulation is about 8 years and is considerably shorter than other insulating investment. Let us show you on the possible promotion opportunities beraten.quelle: trotherm.de




Thursday, January 15, 2009

Pirates Of The Caribbean Prom

RIGIPS:

When testing the neighbors, the new home theater system, children play later in the apartment one floor exercise or is hammered next door late into the night, the strain on the nerves. Subsequent sound insulation with gypsum board products of plaster reduces the noise without much effort.

According to a study by the Spectra research about the relationship of the Austrians with their neighbors noise is at the top of the disturbances. Almost a third of all respondents said they were not feeling the often disturbed by noise from neighboring apartments or neighboring buildings. Some of the main sources of noise pollution, loud noise through crafts, dogs barking, loud music, noisy children and extensive celebrations. Who will no longer angry about stomping, roaring and drilling can protect themselves with subsequent sound remedy.

Basically, noise can be reduced most where it has its source. With dry floor and mineral wool insulation in the floor, the impact sound transmission can be reduced considerably from their own homes. A measure but is usually only for new buildings or major refurbishment in the course possible.

it is much simpler, however, recover a suspended ceiling. These anchors are mounted on the ceiling plaster and fixed to corresponding elements. If, for special Acoustic ceiling panels such as plasterboard or perforated ceilings or coffered ceilings Gyptone Casoprano, improves not only the sound insulation, but creates the new ceiling is also equal to a visual highlight.

impact sound comes not only through the ceiling, but also looks for side roads on adjacent walls. Therefore, a combination of suspended ceiling and wall lining on the walls is most effective. For the front sheet, a substructure of wood or metal is attached to the wall. To reduce the sound transmission at these contact surfaces, a sealing strip is placed between them. The voids between the wood or metal studs are filled with mineral wool and Finally, the plasterboard screwed to the substructure. The surface of the wall is just plastered, painted or papered.

To cut the sound with a few, but very effective measures ab.quelle easy way: bdb.at


Sample Letter Of Appeal

Subsequent Subsequent Subsequently quieter sound insulation cladding of the facade

How much is subsequent improvement in noise control possible?
Let's say that you are separated by a 15 cm thick brick wall of your neighbor. The weighted sound reduction index of this partition is only RW = 45 dB. If you do not want to miss out on your well deserved rest, we recommend the use of ISOVER Acousto-partition-terminal felt. To increase the sound insulation value by as much as 10 dB.

Simple design - high sound insulation.
Share your own sound protection wall. Noise barriers are not just on motorways. Maybe you just need one in your bedroom to be able to sleep again in the future still. Rather than counting sheep, you just need to give space to 10 cm wide and has halved the noise from the neighboring apartment.


How it works: make a lightweight metal stud wall with gypsum board in front of your perceptive wall. The cavity that is created here between the metal studs, to be completed before the installation of the plasterboard with sound-absorbing partition ISOVER acousto-terminal felt. Done!

simple formula - big impact: 1 inch equals 1 dB! source

: isover.at


Thread Sealant How Long To Dry



thermal bridging, moisture damage, mold, excessive heat energy: occasions to reflect on the subsequent covering of the exterior walls of the house.
Bid in the walls of the insulation from the outside or from within. Recommended is the external insulation, which acts as a heat store. There are different ways of external insulation: with thermal insulation composite systems, foam or mineral fiber boards, which are applied directly to the outside wall or a curtain wall, which consists of a supporting structure, insulation and cladding.
an overview of the various solutions and systems for an individual to the respective Port calls, insulation provide you with the dealer. The expert determined the spot the right amount of insulation for the modernization project.

fire

The fire protection requirements to be met for the components of a house are set in the Landesbauverordnungen of the countries.
important measures of preventive fire or fire protection include the use of flame-retardant or noncombustible materials (classification of building, fire resistance classes) and work to install fire-retardant or fire-resistant components, such as fire walls, fire walls, fire doors and as well as to ensure adequate escape and rescue routes.

soundproofing

The subsequent thermal insulation should not deteriorate the sound insulation. You can say simplified, that tough thermal insulation materials deteriorate with rendering the sound insulation, heat insulation materials with improved soft plaster for sound insulation. Thermal insulation, except apparel act for rather neutral.

moisture protection

exterior walls must provide both an adequate rain protection and protection against condensation on the inside of components. The driving rain of heat insulating material may be acting alone, there is an additional layer is required. This layer can, for example be a garment made of wood, slabs or plaster.
need protection from condensation when all the individual layers of the outer wall are considered, the installation of a vapor barrier or vapor barrier may be necessary. If necessary, should be a calculated scan to rule out possible structural damage due to condensation können.quelle: include hausundmarkt.de


Vidios Italianos Grates

sound - or: the door is what matters.

volume and noise of daily life, keep the resulting health risks for people underestimated. The sound insulation in buildings is of great importance, here are particularly sound-proof doors in view. WIRUS soundproof doors meet all official regulations and requirements - and also offer individual solutions.


Just one run at a normal volume conversation reaches 40-50 dB. Sound is transmitted from room to room in many different ways. Ideally, a building will be designed during the planning phase to effective sound insulation. But even if the sound is to be subsequently increased protection and upgraded with soundproof doors, is easily possible. The bottom line is that all the individual components of the soundproof door (door panel, frame, seals and fittings) optimally coordinated. As with WIRUS soundproof doors.
sound is transmitted, among other things through the door. The frame, the joint between door and frame and the joints between the door and bottom contribute to the sound transmission. Although changing the amount of noise protection measures due to the expected noise volume, the components must be perfectly coordinated. The range of doors includes sound elements with appropriate sound insulation seals in one or two levels at the transitions between the door and frame. Basically, for noise control, that all efforts be void if necessary sound insulation seals towards the bottom are missing. Therefore, when integrated WIRUS soundproof doors seals as powerful conclusion to the floor joint.
In the event that it is also a potent smoke, fire or climate protection will be integrated, provides WIRUS all soundproof doors as a multi-purpose doors. As flexible selection of the hardware is handled, the desired functions of the door can be adjusted as individual as the burglar-proof facilities with special security strike plates and reinforced belts with belt pouch.
WIRUS Acoustic doors are available with all common surfaces and shy compared to conventional Interior doors no comparison in terms of design and color selection.
box:
  • The sound insulation effect of a turnkey sound insulation door is only partly on the characteristics of the door leaf. The rating is also based on the following criteria:
  • effective bottom seal
  • effective seal to the frame (three-sided lip seal)
  • avoid faulty secondary paths for the sound, ie, care in the assembly of door leaf and frame
  • Construction of door
  • stamina under different climatic conditions
also allows the diverse WIRUS offer individual solutions adapted to the structural requirements tailored werden.quelle: wirus.de

Carbon Monoxide Poisoning Bad Taste

insulation of music rooms

A frequently asked question of musicians is how to insulate a sample space effectively against noise and unpleasant noise. In this issue must are two things distinguish :

Once it is: in the sound insulation in the sense a noise reduction from the inside out to protect the neighbors, or vice versa from outside to inside to protect against unwanted background noise at sound recordings. In the foreground it is primarily the extent possible, noise elimination.

Secondly, there is demand for the attenuation of reflection with the aim of improving sound in the interior to increase as the recording quality or intelligibility. It is, however, to create a balanced sound image with as good preservation of sound indoors!

So these are two entirely different claims .

The desired return loss is achieved by the skilful and moderate use of absorbers, and soft foam mats in a pyramidal and in a very limited way and with the typical egg cartons. This is however only the higher frequencies. Especially foams act only at frequencies of around 1-2kHz. These represent but in terms of the neighbors is not a problem because they do not penetrate the wall, so for sound insulation foam mats are unfit. The disturbing bass, however, which is perceived very well outside their rooms, will be reduced only by special broadband absorbers and this is not even complete. Such absorbers have therefore only the task of the interior to provide balanced sound. Further action in this regard diffusers the sound reflecting non-specific, rather than destroy it.

foams, carpets and curtains have no real impact to the outside of the insulation!

The only way to prevent noise pursuing a strategy to penetrate the wall and out of the room is to build very thick and hard or to work with additional partitions. Depending on the thick brick walls, or other interior fittings are, the more impenetrable it be for sound vibrations, since the mass movement must be brought into, before they then turn the air on the other hand, stimulate. Decisive here is the so-called basis weight of the material: even relatively strong sound pressure, a heavy and thick wall moves only slightly, sodas and the Run is stimulated only slightly behind. Unfortunately, it is structurally here in retrospect hardly change!

means to insulate an existing room afterwards, therefore, to recover an additional wall and separate the two resulting air spaces completely. To be added to create a separate screened area must be completely dense inner shell. For example you can set up through typical drywall construction a framework type of strips of wood or aluminum profiles, which in turn Chipboard or plasterboard wear. The profiles should be decoupled from the floor and touching the clad plates, the outer wall is not logical. Of course we then need an additional door and window gfs in the original window. These should include well-sealed, ideally, practical! The best way is to old and new doors and fixed optical directly against each other and add a little foam between the frame. The aeration, which are found in small compact shell areas which do not meet the entire room, usually is not necessary: The volume is correspondingly larger and so is in the breaks just passing through 2 windows revealed. The lighting must of course be moved into the interior, as well as electrical connections.

The entire sound insulation effect acts in two ways: First, there are now two walls, through which the sound come through it, and second because of delayed wave reflections at the walls of two spatially overlapping and also to enable cancellation of the same. Moreover, the gap is partially filled with insulating material, to ease the air contained therein. Only the measure of the so-called " room within a room" - principle alone can, against background noise in both directions truly effective manner.

The inside of such a construction sounds, of course, back to the way a vacuum: It whips and slams at every noise and also resonates with the space according to its natural frequencies. The walls must therefore be in accordance with the requirement of a uniform-sounding room to be calmed by appropriate insulation measures.

The crucial point is therefore the double-space system: Simplified one could say that wall thickness and double-space system contribute to the sound quantity, while insulating materials on or prior to defining the wall of sound quality.

On the part of professional manufacturers, there is now a range of solutions for mobile space-in-space concepts: More or less big boxes and booths can be set up later in studios and rehearsal spaces and resume demontieren.quelle: studio96.de


Power Use Pedestal Fan

room acoustics - sound insulation

The field of acoustics is huge. In the interior are interested however, especially the building acoustics and room acoustics. The acoustics deals inter alia with the sound transmission and sound insulation between rooms or between space and the outside world. The acoustics, however, describes the spread of Sound waves within a room.


Room Acoustics / Acoustics in rooms

The acoustics will be influenced by the design of the room so that the acoustic parts of the room to its application as accurately as possible. It must be remembered that a radio or TV studio does not have the same acoustic requirements, such as an auditorium, a church or a theater and a basement meeting room does not have the same acoustics as an open-plan office or living room.

The characteristics of room acoustics for different applications in practice are not compatible fast. Therefore, it is almost impossible to find a universal space to create a perfect example in the speech intelligibility and optimal music experience can be combined. A fix is so furnished room acoustics on a compromise of various properties. This compromise may, however, flexible, mobile elements such as heavy curtains, screens, etc. Akustikörper, optimized to fit the particular requirements.

The room acoustics affect not only our ears but in the long time to come and our health. A room with good acoustics makes for a better well-being and reduces the stress factor of noise. Therefore, it is precisely in places where we spend a long time (eg office) very important that the room acoustics are pleasant.

acoustics / sound

The sound is the sound propagation to be so affected that can penetrate the air-borne noise or sound is not from the room to the outside or from outside the room. That is, target the sound insulation is to separate rooms acoustically.

seismic is in the construction sector as the impact sound is a common problem. Impact noise created by steps, skipping, tapping, etc. are making the walls or ceiling placed on the wave. This, in turn, that by exciting the air and a corresponding air sound thereby generated sounds can be heard from adjoining rooms. Kick or step sound can be achieved by measures körperschalldämmende ("floating floor") or by airborne sound measures (suspended ceilings). Subsequent Schalldämmlösungen but are only effective if it can be accurately assessed, which is transmitted via components of the sound. In most cases, however, the transmission of noise from another room done over multiple paths. That is in addition to directly intervening wall or ceiling, the sound waves penetrate the concrete by lying next to walls or to heating, electricity and water pipes in the room. On an effective sound insulation must be taken during their creation of a space (eg, by acoustic decoupling of individual components). Mistakes are made during the construction or creation of spaces, can be subsequently corrected usually only high financial costs.

airborne is moved by vibration of air in the room and much more ensteht by various noise sources such as voices, music, machines. To prevent the spread of airborne sound to the outside or inside to prevent acoustic and sound insulation measures can be used. Room acoustic measures absorb some of the sound and convert it into heat. This shortens the reverberation time. Sound insulation measures reflect the sound and keep it back in the room or outside the room.

Important
A good sound insulation between two offices is easier to achieve if the acoustics perfect and the reverberation time is not too high. Especially in small rooms (Focus cabins, small meeting rooms, etc.) should necessarily be made a part of the walls with an acoustically active surface. It is hardly ever a good sound insulation between exterior and interior to achieve. Special attention must always be the sound side paths (ducts, ventilation ducts, raised floor, Ceiling cavities, etc.) to be paid. These are often the main cause for problems with the sound and must be sealed with special acoustic materials. This should also be heeded in the construction of a building.

Schalldämmprobleme through the transfer of noise through the pipes, concrete slabs, steel beams, etc., can usually only be resolved later at great expense.

room acoustics problems (eg, reverberant rooms due to long reverberation time) can be subsequently corrected relatively easily.

The right solution for acoustic Your space

We have in our program, many products that can improve the room acoustics and sound insulation in your home. Even for already built spaces with acoustic problems is trim it the perfect solution subsequently the room to the right room acoustics können.quelle: kr-schweiz.ch


Saturday, January 10, 2009

Master Lock Sphere Combo

coconut fiber

The coconut fiber is a lightweight, very elastic and break-resistant fiber and is prepared from the pericarp of the coconut. It is hollow inside, what is due to their high thermal and sound insulation properties. Coir fibers are processed into nonwovens and flexible insulating mats of different thickness.

The insulation properties

coconut fiber has excellent thermal and Schalldämmungseigenschften. By the plant's own tanning coconut fiber has a high resistance against the decay and is resistant to moisture. Insulation made of coconut fibers are also permeable and contribute feutigkeitsregulierend. To achieve the fire protection class B2 normal flammable - the addition of boron salts or ammonium sulfate is required.

application

coconut fiber is very versatile in the heat and sound insulation. Whether as a darning wool for lining remaining areas, the wall insulation in the light or sound insulation and Cavity insulation blankets. Due to its high durability and resistance to moisture, insulation from coconut fiber are often used for insulating moisture sensitive areas such as below screed, basement and exterior wall insulation and insulation between cavity walls. The permeable property of the insulating material coconut fiber makes it particularly interesting for the renovations.

Overview

thermal conductivity: 0.040 to 0.050 W / mK
spec. Heat capacity: 1300-1600 J / kgK
water vapor diffusion resistance: a
Building Class: B 2 normal flammability
Density: 40-120 kg / m?
Primary Energy: 95-200 kWh / m?

source: ecologically-bauen.info


Kurdish Traditional Cloth

wood fiber insulation boards

wood fiber insulation boards (also called soft fiber insulation boards) are manufactured from debarked wood waste. This is ground into fine wood fibers, briefly heated and then pressed into sheets. Serve as an adhesive, the wood's resin, so no further additions required. As a protection against decay and fire protection Vebesserung but ammonium sulfate is added. To the roof insulation wood fiber insulation boards be treated. This is done either with natural resins or bitumen. The latter is not as ecologically meaningful classification.

properties of wood fiber insulation boards

The wood fiber insulation achieves a thermal conductivity of 0.040 to 0.055 W / m² K. Thus, it has a good insulating property. In addition, the wood fiber insulation boards have good sound insulation effect and a high heat storage capacity and have moisture-regulating effect. Wood fiber insulation boards are in the fire protection class B2 - classified - normal flammability. wood fiber insulation boards are offered in different thicknesses as a rigid, pressure-duty insulation and as a flexible insulation panels.

application

wood fiber insulation boards can be used in the intermediate rafters or roof insulation. Furthermore, the wall insulation in drywall and insulation and sound insulation of ceiling . Meanwhile it also dry bar insulation systems are available with wood fiber insulation boards. In general, the wood fiber insulation boards in a circumferential tongue and groove, so that no gaps. Wood fiber panels can be easily edited.

Overview

thermal conductivity: 0.040 to 0.055 W / (m * K)
spec. Heat capacity: 2000-2100 J / (kg * K)
water vapor diffusion resistance: 50-10
Material class B2 normal flammability
Density: 150-190 kg/m3
Primary Energy: 600-1500 kWh/m3

source: ecologically-bauen.info


How To Tie A Bandana Around Your Snowboard

cellulose flakes: from old to new

the organic insulating materials to the cellulose fiber is currently the most important. This is certainly attributable to the fact that cellulose insulation products are fully competitive with conventional insulation materials like mineral wool or foam insulation. In addition, the special suitability of wood frame construction.

production

cellulose flakes are made from recycled paper, which typically originates from daily newspapers. The paper is in several steps mechanically crushed and frayed. This changes the cellulose their structure is a snippet from a paper three-dimensional cellulose flake that offers through their networking with each other a high level of security setting. After the addition of boron salts (15%) is cellulose insulation in all the fire class B2 - reached normal flammability. Some new products, even the fire class B1 - entflammber. This addition also protects against mold infestation. Some manufacturers now offer free and borate cellulose flakes. As fire protection and fungicide agents are here then ammonium salts or aluminum salts. Trade names for the cellulose insulation flakes include Isoflock and Climacell.

properties

cellulose flakes have a thermal conductivity of 0.040 to 0.045 W / m² K is a very good insulation and provide good sound insulation properties. It contains no chemicals exhaling, is vapor permeable and has a moisture-regulating.

application

cellulose flakes can be used in many ways. The following processing procedures are common in practice:

  • lot heaping
  • Open-blowing
  • Filling cavity blowing in air-tight cavities
  • Feuchtsprühverfahren

The trade name for cellulose flakes include Climacell or Isflock

Overview

thermal conductivity: 0.040 to 0.045 W / (m K?)
spec. Heat capacity: 1700-2150 J / (? Kg K)
water vapor diffusion resistance: 1-2
Building Class: B 2 normal flammability
Rohdichte: 30-80 kg / m?
Primärenergiegehalt: 50 kWh / m?


Quelle: oekologisch-bauen.info